Home > Body Chrome Molding > 1982 - 1992 Firebird Pre-Cut Body Side Trim Molding Set with Pointed Ends
Alternative Views:	Our Price: $109.95 Sale Price: $99.95 You save $10.00! PART NUMBER: BCM-125 Qty:

Description Technical Specs   1982 - 1992 Firebird or Trans Am PRE-CUT Body Side Trim Molding Set with Pointed Ends New 1982 - 1992 Firebird or Trans Am exterior body side trim molding set. Perfect fit for all 82 - 92 models. This new set comes complete with PRE-CUT PIECES and the ends come to a point like originals. Measures just under 1 inch wide at 15 / 16". Installs in minutes! This kit comes with (6) PRE-CUT strips, (2) Fender Pieces, (2) Door Pieces and (2) Rear Quarter Pieces. Manufactured with original equipment approved polymers, Mylar laminates and 3M acrylic foam tape on the back side for a quick easy installation! Outstanding performance and reliability. Complete set to do both sides! Order your new Body Side Molding Kit today!! *This kit comes Black in color and is paintable if you desire. PART NUMBER: BCM-125 Application Procedures for Pressure-Sensitive Body Side Moldings Outlined below are the recommended procedures for applying pressure-sensitive Body Side Moldings (BSM). These procedures address the key points for a successful BSM application. The body of the vehicle must be clean and dry to achieve the best adhesion. The pressure-sensitive adhesive on the molding must not be contaminated during the application. The molding must be applied to achieve complete contact (bond) of the adhesive to the vehicle. (i.e. maximum wet-out). Installation Area: The installation area should be kept reasonably clean. Any airborne dust, oils, etc. may contaminate the vehicle or BSM adhesive and reduce the bond of the tape. Vehicle Surface Preparation: The vehicle surface should be washed with an appropriate solvent, one commonly used system is a 70% mixture of Isopropyl Alcohol and water (Rubbing Alcohol). To assure removal of all contaminants it may be necessary to first wipe with TG Prep, then use the 70% Isopropyl Alcohol mixture. * Use clean lint free wiping cloths or disposable wipes such as Kim wipes. * Reprocessed rags should not be used as they may contain wax or residue. Step 1 After washing, the vehicle surface should be thoroughly dried. Again use a clean, dry, lint free cloth. Vehicle surface application temperatures of 80'F (26'C) to 110'F (44'C) are recommended for best tape adhesion. The warmer surface will help wet-out the adhesive on the tape. During cold weather applications the vehicle surface can be heated with a heat gun or heat lamps, but do not heat the surface of the molding. Application of the BSM at temperatures below 64'F (17'C) or above 110'F (44'C) must be avoided. Step 2 Body Side Molding Preparation: The BSM should be stored at room temperature in a clean dry area. Cold temperatures require heating to warm the molding to the proper application temperature (i.e. Floor heater of vehicle). There is no damage to the tape or molding stored at colder temperatures, but moisture and condensation must be avoided. The molding can be heated up to 100'F (38'C) for application. This will soften the molding, making it easier to conform to the vehicle contours, as well as improve adhesive wet-out. The liner on the adhesive should not be removed until application to the vehicle. This will help prevent contamination of the adhesive surface. Body Side Molding Application: Align the molding with a key feature such as the front and rear bumpers or with a body line to ensure proper molding alignment. Placing ½" masking tape along the desired installation area is an excellent guide for applying the molding straight. Step 3 Be certain to leave enough room for the door to open properly after the molding has been installed. (Bevel cut if necessary). Step 4 Remove the liner from the tape as you are applying the molding to the vehicle. Be careful not to contaminate the adhesive. Common sources of contamination are: oil from the applicator hands, dust or lint from clothing, work tables, or the floor. Do not touch the adhesive at any time. Contaminated moldings should not be used Step 5 Apply the moldings with a rolling motion to prevent entrapment of air between the tape and the vehicle surface. Use firm hand pressure to ensure good adhesion of the molding. Step 6 A roll down with a hard rubber hand roller is recommended to assure complete wet-out of the adhesive to the vehicle surface. Apply firm pressure while rolling the molding to properly wet-out the adhesive. Step 7 Check the edges of the molding to assure good tape adhesion. Re-roll with more pressure as necessary to achieve a good bond. Step 8 Enjoy the fresh clean look of your new body side trim! Features PRE-CUT 15 / 16" Wide with Pointed Ends 3M Acrylic Foam Tape Pre-Installed Other great products you might need 1982 - 1992 Firebird F-Body Upper Door Hinge - RH / LH 1970 - 1992 Firebird OE Style 18" Windshield Wiper Blade, Black, Each 1982 - 1992 Firebird Interior Rear Hatch Cargo Panel Plastic Trim Screw, Each 1987 - 1992 Firebird and Trans Am Body Side Trim Molding Set with Pointed Ends Our Price: $94.95 Add Sale Price: $17.95 Add Our Price: $3.95 Add Our Price: $94.98 Add 1982 - 1992 Firebird Outer Window Felts Pair 1982 - 2002 Firebird & Trans Am Antenna, Custom Shorty 8 Inch with BLACK FINISH 1982 - 1992 Firebird Door Jamb Sill Plate, NEW PAIR, Choose Color Our Price: $64.95 Add Our Price: $18.95 Add Our Price: $139.95 Add

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item: Body Chrome Molding 82-92 New Parts